Designed & Made in the USA Since 1983
Every Mitutoyo Digimatic connector type mapped to its gage family, cable part number, output protocol, and compatible MicroRidge interface — in one place.
This post is also available in:
Ordering the wrong Mitutoyo SPC cable is a recurring sourcing error that grounds inspection stations, delays production, and is entirely avoidable. The Digimatic protocol is consistent across most of the Mitutoyo instrument lineup, but the physical connector on the gage side varies significantly by instrument family. One connector type is compatible with your 500-series Absolute caliper; a completely different one fits your micrometer; another is required for your ID-C indicator. And if your ID-C was purchased after 2023, neither of those is correct.
Every gage covered in this guide can be connected to either a GageWay wired interface or a MobileCollect wireless system — the cable determines the gage-side connection, not the data collection path. This guide organizes every current Mitutoyo Digimatic SPC cable by physical connection group, maps each group to its applicable gage series, and identifies which cables include a data-send button. Use it as a definitive sourcing reference before your next purchase order.
Note: The cable part numbers in this guide apply to the standard Digimatic data output path used with GageWay wired interfaces. If you are sourcing cables for a third-party gage interface, the GageWay wired cable part numbers (905338, 959149, 937387, etc.) are the correct OEM Mitutoyo references to follow. MobileCollect Wireless connector cables are MicroRidge-specific and are not compatible with other gage interfaces. If you are connecting MobileCollect to a Mitutoyo DP-1VA Logger, see the MobileCollect to DP-1VA adapter. If you are sourcing cables for Mitutoyo’s USB Input Tool Direct (USB-ITN) or U-WAVE-T wireless system, the physical connector types are the same but the SKUs differ — refer to the current Mitutoyo catalog or contact MicroRidge for the correct part numbers.
Before mapping cables to gages, two distinctions matter. First, Mitutoyo Digimatic SPC output exists in two protocol variants: D1 (standard Digimatic, used across all current instrument families except the NX-series) and D2 (higher-resolution packet format, exclusive to NX-series ID-C and ID-F indicators). D1 and D2 differ at the data packet level — they are not interchangeable at the protocol layer, though both are read by the same GageWay and MobileCollect interfaces. Second, and independently of the protocol variant, the physical connector on the gage side varies significantly by instrument family. Most sourcing errors trace to the connector, not the protocol — but both matter.
This matters for infrastructure planning: GageWay wired interfaces and MobileCollect wireless transmitters are parallel data collection paths — not combinable on the same signal chain — and the correct choice depends on whether your measurement stations are fixed or portable, not on gage type. Either path can serve the full Mitutoyo instrument lineup.
The connector architecture differs by interface family. GageWay interfaces (SM, KW, Pro) and the MobileCollect Digital Remote accept standard OEM Mitutoyo SPC cables directly at a standard Digimatic header — the part numbers in this guide apply directly. MobileCollect transmitters use proprietary MicroRidge pigtail connectors on the gage side; the Mini Mobile Module EVO (M3E) and Command Mobile Module use different proprietary connectors and are not cross-compatible with each other or with standard OEM Mitutoyo cables. MobileCollect cables are ordered by transmitter model and gage type through MicroRidge. The gage-side connector type is what determines which cable you need regardless of which interface path you choose.
The following table summarizes every current connector type from Mitutoyo’s SPC cable compatibility chart, with part numbers for both 1-meter (40″) and 2-meter (80″) lengths.
Type | Form Factor | Data Button | Output Protocol | Part Number | Primary Gage Category | ||
|---|---|---|---|---|---|---|---|
A |  | Straight water-proof with output button | Yes | Digimatic | 05CZA624 1 meter | 05CZA625 2 meter | IP-rated Digimatic calipers |
B |  | Flat L-Shape water-proof with output button | Yes | Digimatic | 05CZA662 1 meter | 05CZA663 2 meter | IP-rated Digimatic instruments (micrometers) |
C |  | Straight with output button | Yes | Digimatic | 959149 1 meter | 959150 2 meter | Digimatic calipers (Absolute encoder) |
CR |  | L-shape, outlet right with output button | Yes | Digimatic | 04AZB512 1 meter | 04AZB513 2 meter | Micrometers, right-exit variant, custom implementations |
D |  | Flat 10-pin | No | Digimatic | 936937 1 meter | 965014 2 meter | Indicators (ID-H, ID-F), height gages, gage counters, bench systems |
E |  | Round 6-pin | No | Digimatic | 937387 1 meter | 965013 2 meter | Hardness testers (HM series); legacy micrometers, Bench Mike |
F |  | Flat straight | No | Digimatic | 905338 1 meter | 905409 2 meter | Indicators, depth gages, scale units |
FB | 905338 connector but L-shaped with outlet in the back. | No | Digimatic | 905689 1 meter | 905690 2 meter | Indicators, height gages (back-exit variant) | |
FR |  | L-shape, outlet right | No | Digimatic | 905691 1 meter | 905692 2 meter | Indicators, height gages (right-exit variant) |
FL |  | L-shape, outlet left | No | Digimatic | 905693 1 meter | 905694 2 meter | Indicators, height gages (left-exit variant) |
G |  | Flat straight, water-proof | No | Digimatic | 21EAA194 1 meter | 21EAA190 2 meter | ID-N/ID-B coolant-proof indicators |
SA |  | Water-proof, straight with output button | Yes | Digimatic D2 + S1 | 06AGL111 1 meter | 06AGL121 2 meter | MDE QuantuMike Series 293 (2024+) |
SF |  | Flat straight standard | No | Digimatic D2 + S1 | 06AGL011 1 meter | 06AGL021 2 meter | NX indicators (ID-CNX, ID-FNX), depth & thickness gages, LH-600F |
D2 = higher-resolution output (to 0.5 µm / 20 µin) — active now on any GageWay or MobileCollect interface running firmware v5.35+. S1 = instrument-level query protocol; unlike standard Digimatic (which can only request a measurement reading), S1 allows the interface to query the gage directly for instrument metadata such as serial number, model, and calibration data. S1 query capability requires both the 06AGL011/06AGL111 cable and an NX-series gage — it is not available on any other cable type. MicroRidge’s GageSync is the first interface implementation to surface S1 instrument data. Available now on the Mini Mobile Module EVO (M3E) and the Shape Transmitter MC-S-MIC02.
Every current model number Mitutoyo lists for each connector type, in one place. Find the model number printed on your instrument, then read across for the cable part number you need.
Older or discontinued gages. Mitutoyo publishes model compatibility for currently available instruments only, so a legacy gage may not appear in the table. Three ways to identify the right cable anyway: check the MobileCollect Selection Tool, which covers many discontinued gages by model number, compare the Digimatic port on your gage against the connector photos in the reference table below, or read the part number printed on the cable you’re already using. If none of those settles it, send us your gage model and we’ll confirm the correct replacement — sales@microridge.com.
Type | Cable (1m / 2m) | Data Switch | Applicable Mitutoyo Models |
|---|---|---|---|
A Water-proof straight, output button | 05CZA624 / 05CZA625 | Yes | Calipers: 500-776/500-777, 500-712-20/500-713-20, 500-712, 550-301-10/550-331-10, 551-301-10/551-331-10, 552-302-10/552-303-10, 552-150-10/552-151-10, 552-155-10/552-156-10, 552-181-10/552-182-10, 573-601/573-602 Depth gage: 571-251-10/571-252-10 Scale unit: 572-600, 572-601 |
B Water-proof L-shape, output button | 05CZA662 / 05CZA663 | Yes | Micrometers: 293-140-30/293-141-30, 293-230-30, 293-666-20/293-667-20, 340-251-30/340-252-30, 227-201-20/227-203-20, 227-205-20/227-206-20, 227-221-20, 227-223-20, 422-230-30/422-231-30, 406-250-30/406-251-30, 343-250-30/343-251-30, 369-250-30/369-251-30, 345-250-30/345-251-30, 314-251-30/314-252-30 Micrometer head: 350-251-30/350-261-30 Holtest: 468-161/468-162 Depth gage: 329-250-30/329-251-30 |
C Straight, output button | 959149 / 959150 | Yes | Calipers: 500-150-30/500-151-30, 500-500-10/500-501-10, 500-443, 573-118-10/573-119-10, 573-116-10/573-117-10, 573-191-30/573-291-30 Depth gage: 571-201-30/571-202-30 Micrometer head: 164-163/164-164 Scale unit: 572-203-10/572-213-10, 572-300-10/572-301-10 |
CR L-shape right exit, output button | 04AZB512 / 04AZB513 | Yes | Micrometers: 293-582/293-583, 389-514/389-714 |
D Flat 10-pin | 936937 / 965014 | No | Indicators: ID-H, ID-F Height gage: QMH-AX/BX Mu-checker: Digital Mu Checker Laser scan micrometer: LSM-9506 Gage counters: EF/EH, EB, EC-101D Litematic: VL-B/S-B Surface roughness: SJ-210/310/410, SJ-500/SV-2100 Hardness testers: HM-210/220, HV-110/120, HR-530, HR-600 |
E Round 6-pin | 937387 / 965013 | No | Hardness testers: HM-102, HM-103, HM-320, HM-430, HM-411 Legacy: older Digimatic micrometers, Bench Mike |
F Flat straight | 905338 / 905409 | No | Indicators: ID-CX, ID-C112AX, ID-C112RXB, ID-C112GXB, ID-U, ID-SS, ID-SX, HDM-AX, HD-AX, HDS-HC, HDS-C ABS Borematic: 568-361/568-362 Scale units: SD-E, SDV-E, SD-F, SDV-F Bore gage: 511-501/511-502 Hardness tester: HH-300 Depth gage: Digimatic type (ID-CX) |
FB Flat L-shape, back exit | 905689 / 905690 | No | Same models as Type F Differs only in cable exit direction |
FR Flat L-shape, right exit | 905691 / 905692 | No | Same models as Type F Differs only in cable exit direction |
FL Flat L-shape, left exit | 905693 / 905694 | No | Same models as Type F Differs only in cable exit direction |
G Flat straight, water-proof | 21EAA194 / 21EAA190 | No | Indicators: ID-N, ID-B |
SA Water-proof straight, output button | 06AGL111 / 06AGL121 | Yes | Micrometer: QuantuMike 293-14X-40 / 293-18X-40 |
SF Straight standard | 06AGL011 / 06AGL021 | No | Indicators: ID-CNX, ID-FNX Depth gage: Digimatic type (ID-CNX) Thickness gage: Digimatic type (ID-CNX) Surface roughness: SJ-220 High-accuracy height gage: LH-600F |
Cables in this group: 905338 · 959149 · 04AZB512 · 905689 · 905691 · 905693
All cables in this group share the same physical gage-side Digimatic connector and are physically interchangeable at the gage port. The differences are cable geometry (straight vs. angled exit) and whether a data-send button is present — not the connector itself. All use Digimatic D1 protocol.
Cable | Button | Exit | Primary Use |
|---|---|---|---|
905338 (1m) / 905409 (2m) | No | Straight | Indicators, height gages, depth gages, scale units, thickness gages |
959149 (1m) / 959150 (2m) | Yes | Straight | Absolute Digimatic calipers, operator-triggered read stations |
04AZB512 (1m) / 04AZB513 (2m) | Yes | L-shape, right exit | Calipers where right-angle cable routing is required |
905689 (1m) / 905690 (2m) | No | L-shape, back exit | Indicators, height gages mounted with back cable exit |
905691 (1m) / 905692 (2m) | No | L-shape, right exit | Indicators, height gages mounted with right cable exit |
905693 (1m) / 905694 (2m) | No | L-shape, left exit | Indicators, height gages mounted with left cable exit |
On interchangeability: Because the gage-side connector is identical across this group, a 959149 will physically mate with an indicator that normally takes a 905338, and vice versa. The button is the deciding factor for workflow — indicator stations typically rely on foot switch or interface-triggered reads, while caliper stations frequently use the data-send button for operator-controlled read cycles. Using a 959149 on an indicator is functional but suboptimal; using a 905338 on a caliper means the operator loses the button and must use a foot switch or hand switch instead. Match the cable to the workflow, not just the connector.
Applicable instruments — 905338 / angled no-button variants:
Applicable instruments — 959149 / button variants:
Cables in this group: 05CZA624 · 05CZA662
Types A (05CZA624) and B (05CZA662) share the same water-proof Digimatic connector and are physically interchangeable at the gage port. Both include a data-send button and are designed for IP-rated instruments in wash-down, coolant-exposure, or high-humidity environments. The distinction between them is which instrument family each is specified for — calipers vs. micrometers.
Skip the cable entirely. The Shape Mic 01 Transmitter MC-S-MIC01 mounts directly to the 5-pin Digimatic SPC port used by these micrometers. One component, one part number, no cable and no separate connector. Covers 500+ Mitutoyo micrometer models across 18 series.
Cable | Primary Use |
|---|---|
05CZA624 (1m) / 05CZA625 (2m) | Coolant-proof Digimatic calipers |
05CZA662 (1m) / 05CZA663 (2m) | Coolant-proof Digimatic micrometers |
Applicable instruments — 05CZA624 (calipers and related):
Applicable instruments — 05CZA662 (micrometers and related):
On interchangeability: Because the gage-side connector is identical between Type A and Type B, either cable will physically mate with any instrument in this group regardless of the specified designation. If your measurement station layout makes one cable’s geometry more practical — a micrometer in a fixed stand where the caliper-specified cable routes more cleanly, for example — the swap is physically and electrically valid. Both carry the same D1 Digimatic protocol and data-send button circuit.
Cable: 937387 (1m) / 965013 (2m) — No data-send button.
The 937387 is the SPC cable for Mitutoyo hardness testing machines using the round 6-pin Digimatic connector (Type E). This connector is physically distinct from the flat connectors used in every other group — there is no cross-compatibility with those cables.
Applicable instruments:
Reads are triggered by foot switch or interface, same as the rest of the lineup. On hardness testers this is typically wired through the tester’s own data-output port rather than a handheld gage, so check your tester’s manual for the specific trigger method it supports.
Cable: 936937 (1m) / 965014 (2m) — No data-send button.
The 936937 (1m) / 965014 (2m) cable covers Mitutoyo indicators, gages, and bench instruments using the flat 10-pin Digimatic connection (Type D). No data-send button. The Type D gage-side shell geometry differs from Group 1 despite a similar appearance — the two are not physically interchangeable.
Applicable instruments:
For the full series list, cross-reference the Type D column in the Mitutoyo Compatibility Lists of Digimatic Gages and Connecting Cables.
Cable: 21EAA194 (1m) / 21EAA190 (2m) — No data-send button.
The 21EAA194 is the SPC cable for Mitutoyo’s ID-N and ID-B indicators — the coolant-proof (IP66) variants of the standard indicator series. Common in machine-side applications where cutting fluid exposure is a design constraint. The water-sealed gage-side connector is unique to this group; the Digimatic D1 output is standard and compatible with all GageWay and MobileCollect interfaces.
Applicable instruments:
Cables in this group: 06AGL011 · 06AGL111
The 06AGL011 (Type SF, no button) and 06AGL111 (Type SA, water-resistant with button) share the same NX-series SF gage-side connector and are physically interchangeable at the gage port. Their primary use cases are distinct — the 06AGL011 is specified for NX-series indicators, while the 06AGL111 is the primary cable for the Mitutoyo MDE QuantuMike Series 293 Coolant Proof IP65 Micrometers. Because they share the same physical connection, the 06AGL111 can also serve as the only option for an NX-series indicator application where an operator data-send button is required, though its water-resistant shell and retention screws make it less convenient in that context.
Skip the cable entirely. For the QuantuMike, the Shape Mic 02 Transmitter (MC-S-MIC02) mounts directly to the SF port as one component, no cable and no separate connector. Because that port carries S1, it supports both TriggerSync and GageSync.
Cable | Button | Exit | Primary Use |
|---|---|---|---|
06AGL011 (1m) / 06AGL021 (2m) | No | Standard – flat straight | NX-series ID-C/ID-F indicators (543-70X, 543-71X, 543-72X, 543-73X), SJ-220 Surface Roughness, LH-600F Height Gage |
06AGL111 (1m) / 06AGL121 (2m) | Yes | Water-proof with retention screws – flat straight | MDE QuantuMike Series 293 Coolant Proof IP65 Micrometers |
This group is not interchangeable with any other connection group. The SF connector will not mate with a pre-NX indicator or any standard Digimatic instrument that uses a Group 1 through 5 connector, and vice versa. This is a deliberate physical break — Mitutoyo changed the connector specifically to support D2 and S1 protocol capabilities that the previous connector geometry could not reliably carry.
The SF connector arrived on two separate instrument families at different times. In 2023, Mitutoyo introduced the NX-series ID-C and ID-F Digimatic indicators — Series 543-70X, 543-71X, 543-72X, and 543-73X — replacing the Type F port with the new SF connector. In 2024–2025, Mitutoyo extended the SF connector to the QuantuMike Series 293 Coolant Proof IP65 Micrometers. Both instrument families use the same physical connection and are served by the same cable group, but if you purchased a QuantuMike before the connector update you may still have the previous cable type — verify before ordering. Both transitions introduced two protocol capabilities not present on any other connection group:
Digimatic D2 delivers higher-resolution measurement output — down to 0.5 µm / 20 µin — and represents a meaningful step forward in precision data collection. D2 is fully supported across the MicroRidge lineup, including all GageWay wired interfaces and MobileCollect wireless transmitters.
Digimatic S1 is a true instrument-level query protocol — qualitatively different from standard Digimatic. Where standard Digimatic is unidirectional (the interface asserts REQ, the gage outputs a measurement reading, transaction complete), S1 allows the interface to query the instrument directly for metadata: serial number, model identification, calibration data. This enables traceability at the instrument level, not just the measurement level — the data collection system can verify which instrument produced a reading, not just record the value.
GageSync, MicroRidge’s S1 implementation, is available now on the Mini Mobile Module EVO (M3E) and on the Shape Transmitter MC-S-MIC02 for the QuantuMike. It surfaces S1 instrument data to your SPC or quality management system through the MobileCollect EVO API, which requires an EVO Base Receiver on firmware 6.30 or higher and an application that implements the API commands. If your traceability requirements extend to instrument-level data, the M3E with the 06AGL011 covers NX-series indicators, and the MC-S-MIC02 covers the QuantuMike as a single cable-free component.
How to identify a Group 6 instrument:
For a full breakdown of the shift to the SF connector, what changed, and which instruments are affected, read the complete guide here: Mitutoyo SPC Cable Connector Changes: 06AGL011, 06AGL111, and the NX-Series Shift.
Selecting the correct cable resolves the gage-side connection. The other end of the signal path — from cable to SPC software — is where MicroRidge interfaces come in.
Wired data collection (GageWay):
The GageWay product line accepts all Digimatic SPC cable types and outputs measurement data via virtual COM port (GageWay SM) or as keyboard wedge keystrokes directly into Excel, cloud-based SPC, or any accepting application (GageWay KW) — no additional software required. GageWay Pro supports multi-gage configurations and also outputs via keyboard wedge and COM port, making it the wired option for multi-station inspection cells feeding a single SPC application. No baud rate configuration or communication parameters are required — Digimatic is pre-configured.
Wireless data collection (MobileCollect RM2.4):
MobileCollect replaces the wired cable-to-interface run with a wireless RM2.4 link operating on IEEE 802.15.4 at 32-bit encryption. The Mini Mobile Module EVO M3E transmitter attaches directly to the gage via a MobileCollect cable connector (the short pigtail that replaces the wired SPC cable). A MobileCollect Base Receiver connects to the workstation and presents data to your SPC software on a virtual COM port or as keyboard wedge keystrokes directly into Excel, cloud-based SPC, or any accepting application, without additional software.
MobileCollect runs on RM2.4 — an industrial-grade wireless protocol built specifically for transferring measurement data from precision instruments on the shop floor. Where Bluetooth and Wi-Fi introduce interference, dropped readings, and security gaps in manufacturing environments, RM2.4 operates on IEEE 802.15.4 with 32-bit encryption, purpose-designed for reliable gage data collection.
→ Why RM2.4 outperforms Bluetooth in manufacturing
Finding MobileCollect wireless cable part numbers: The wireless connector part numbers for each gage type are listed under the Wireless Options section on the corresponding OEM cable product pages. Start with the OEM cable that matches your gage’s connection group, then find the wireless equivalent in the Wireless Options section. For example, the 905338 product page lists the compatible MobileCollect Wireless connectors for each MobileCollect transmitter model. The MobileCollect Selection Tool can also be used to find the MobileCollect Wireless part numbers.
Decision framework:
Use the MobileCollect Selection Tool to search by gage model number or OEM part code. The database indexes 3,500+ gages including Mitutoyo instruments with connector type, recommended MicroRidge cable, and compatible interface pre-mapped.
The gage code is typically printed on the back or bottom of the instrument. Enter it directly into the Selection Tool, or contact us at sales@microridge.com to confirm the correct cable and interface configuration for your specific measurement station layout.
Can I use a 959149 on an indicator that normally takes a 905338?
Physically, yes — both are Group 1 cables and share the same gage-side connector. The 959149 will mate with any indicator that takes the 905338. In practice, the data-send button on the 959149 is simply unused in that application. The more common issue is the reverse: using a 905338 on a caliper station where the operator expects a button-triggered read cycle. That works electrically but changes the workflow — reads must come from a foot switch or the interface instead.
My indicator is a Series 543 — how do I know if it takes the 905338 or the 06AGL011?
Check the series code on the instrument. Pre-2023 ID-C and ID-F indicators (543-200 through 543-6XX range) use the 905338 Group 1 connector. NX-series indicators introduced in 2023 (543-70X, 543-71X, 543-72X, 543-73X) use the 06AGL011 Group 6 SF connector. The two connectors are not physically interchangeable — if the cable won’t seat, you have the wrong group. Use the MobileCollect Selection Tool to confirm by model number.
I have a mixed gage floor — some micrometers, some calipers, some indicators. Do I need a different interface for each cable type?
No. All connection groups feed the same Digimatic protocol into your GageWay or MobileCollect interface. GageWay Pro supports multi-gage configurations across mixed cable types on a single interface. MobileCollect handles mixed fleets wirelessly with each transmitter paired to its gage regardless of cable group. Group 6 instruments with D2 output are fully supported across the MicroRidge lineup.
What’s the difference between the 05CZA624 and 05CZA662 — can I use either on my IP-rated gage?
Both are Group 2 cables with the same water-resistant gage-side connector, so either will physically mate with any instrument in the group. The 05CZA624 is specified for coolant-proof calipers; the 05CZA662 for coolant-proof micrometers. If your measurement station layout makes one cable’s geometry more practical than the other, the swap is electrically valid.
What does “S1” actually mean for my data collection setup — and does it work today?
S1 is an instrument-level query protocol supported by NX-series indicators (via the 06AGL011) and QuantuMike IP65 micrometers (via the 06AGL111). Where standard Digimatic is a one-way transaction (REQ → measurement reading), S1 allows the interface to query the gage directly for instrument metadata: serial number, model identification, calibration data. This enables traceability at the instrument level, not just the measurement level. MicroRidge’s GageSync feature surfaces this data through the M3E transmitter and the Shape Transmitter Mic 02 (MC-S-MIC02), and is available now. It is implemented in your SPC software through the MobileCollect EVO API.
Can I extend cable length?
Yes — the G-EXT extension cable adds 8 feet of in-line length between any Digimatic SPC cable and your interface, without signal degradation.
Is there a wireless option that does not use a cable?
Yes, for Mitutoyo micrometers. Shape Transmitters mount directly to the gage’s SPC port as a single component, replacing both the gage connector and the transmitter. The MC-S-MIC01 covers micrometers with the Group 2 5-pin port, and the MC-S-MIC02 covers the MDE QuantuMike with the Group 6 Type SA port.
MicroRidge is a Certified Mitutoyo Distributor. All cable types referenced in this guide are OEM Mitutoyo products sold through MicroRidge. For instruments not listed or recently introduced models, contact us at sales@microridge.com for cable type verification before ordering.
Riley Tronson is President and owner of MicroRidge Systems, a role held since 2023. Riley brings a strong technical foundation to leadership in measurement solutions. An experienced entrepreneur, Riley has founded and grown multiple software companies, including a venture focused on developing iPhone applications, blending engineering expertise with innovative product development.